If you are looking for high-quality products, please feel free to contact us and send an inquiry, email: brad@ihpa.net
What’s zirconium-nitride? ZrN, zirconium-nitride, has excellent corrosion resistance and good lubricity. It is an attractive coating due to these properties. It is applied using physical vapor deposition. You can choose from a beautiful yellow or crystalline coating. Zirconium Nitride has the following physical and chemical characteristics: a density of 7.09; a microhardness around 980019600MPa and a melting temperature (2980 plus/minus 50)°C. Due to its many properties, Zirconium Nitride (ZrN), can be used in many different ways. ZrN is slightly golden when grown via physical vapor deposit (PVD). It looks similar to elemental. ZrN’s room temperature resistivity is 12.0cm. It has a temperature coefficient 5.610-8cm/K. Superconducting temperature is 10.4K. Relaxation lattice parameter 0.4575nm. ZrN, a single-crystal ZrN has a hardness of 22.71.7 GPa. The elastic modulus is 450 GPa. Why zirconium-nitride is used. Zirconium-nitride, a hard ceramic similar to titan nitride, is also a cement-like material and a refractory. This makes it suitable for laboratory crucibles as well as cermets and refractory materials. It is often used in coatings such as medical equipment and parts of the aerospace, automotive, and aviation industries. Al is alloyed with cubic ZrN, and the electronic structure results from this local octahedral-bond symmetry. The Al content will increase, and the symmetry of cubic ZrN becomes more complex. As a hydrogen peroxide fuel tank liner for airplanes and rockets, zirconium nutride should be used. Zirconium-nitride compounds (ZrN), have crystal structures that change with their composition. The ZrN, Zr3N4 or c-Zr3N4 alloy compounds have been identified in Zr-N’s Zr-N system. Not only do they have great chemical properties but they can also be used to make junctions, diffusion lams, and other low-temperature instruments. they can be used to make integrated three-dimensional electric coils or metal-based transistors. In addition, ZrN compounds have superior wear resistance as well as oxidation and corrosion resistance. Prepare zirconium-nitride powder Direct nitridation with Zr, nitrogen, high-energy reactive balls milling (RBM), microwave radiation method, benzene thermo method, aluminum reduction (N) and direct carbon therm nitriding zirconia. You can use these routes to produce different size and morphologies of particles. You can mass produce zirconium trioxide or other transition metal nitrides by using fibers, microspheres as well as membranes, blocks, and also have the option of manufacturing them in large quantities. Due to the formation of solid solution within the ZrNZrC–’ZrO” systems, the final product nitriding is typically represented by Zr (N.C., O). A CRN process Requires two-step heat treatment. As an intermediate, Zirconium Carbide (ZrC), which is then made into Nitride, must be used. But, the CN procedure is the direct nitridation ZrO2 in presence of carbon. This requires only one heat treatment. In preparing zirconium nutride powder, the latter is likely to be faster and more cost-effective. Zirconium-nitride catalyst exceeds platinum for oxygen reduction Materials made of platinum (Pt), which are based on metal-air batteries and microelectronic sensors make up a significant part of automotive catalytic convertors, electrochemical energy converter equipment, and anti-cancer medicines. While Pt is the most widely used catalyst for oxygen reduction (ORR), in fuel cells or metal-air battery, its scaleability and cost are limited. This paper shows that nano-particle zirconium (ZrN), which can also be used to catalyze ORR in alkaline environment, is able to replace and even surpass Pt. The ZrN nanoparticles are synthesized from carbon-supported platinum (Pt/C). They have similar activity to the Pt/C catalyst. The half-wave potential of both materials is the same (E1/2 = 0.80 V), after 1000 ORR cycles. ZrN also has higher stability than Pt/C catalyst (E1/2 than =-3 mV; E1/2 =-3 mV). KOH, 0.1 M. ZrN is also more efficient than Pt/C when used in zinc-air battery batteries. ZrN is a cost-saving option that can replace Pt/C. ZrN also has a higher power density and cycle capability than Pt/C. ZrN might be helpful in other catalytic methods. Enhanced photoluminescence paired with a periodic array organic dyes and nanoparticles zirconium trioxide Due to their good optical properties in plasma technology, noble metals such as gold are routinely employed. The melting point of gold is extremely low. This is especially true for nanoscale. Also, there is a low amount of gold within the Earth’s crust. The material limitations prevent the exploration of plasmons for multiple fields. These plasmons are promising substitutes for metals because they have excellent mechanical and thermal stability as well as acceptable plasma characteristics in visible spectrum. Zirconium-nitride is an attractive alternative to titanium nitride. In fact, its carrier density exceeds that of TiN. Additionally, titanium nitride is considered the most researched gold supplementary material. This study fabricated ZrN nanoparticles in a periodic arrangement. The array increased the intensity of organic dyes by 9.7x. These experiments proved that ZrN could be used to develop and improve plasmons as well as to overcome limitations inherent in gold. TRUNNANO is also known as. Lempotee Nano Technology Co. Ltd. is a reliable global supplier and manufacturer of chemical materials. They have over 12 years experience providing high-quality, super-high quality chemicals as well as Nanomaterials. Our company currently has a variety of products.
Inquiry us
